This free survey is powered by
  1. Surveys
  2. 2013
  3. February
  4. T
  5. Test Controller
0%
Exit Survey
 
 
Thank you for purchasing a Munters unit.

As a purchaser of a Munters Industrial Dehumidificaton / Air Handling Unit in the last 4 years, we invite you to take part in a brief (5 minutes) survey to provide input on the selection of programmable controllers for Munters US Industrial Product Lines (ICA and HCDs). Your opinions are very important to us.

This survey only applies to the Munters Industrial ICA and HCD product lines. These industrial product, manufactured out of the Amesbury, Massachusetts facility will be utilizing a new controller on our baseline products during the 2013 calendar year, due to the phase out of the S7-200 product by Siemens*. Munters will continue to maintain our status quo and support customer's unique needs with the platforms of their choice

Munters commercial product lines (Drycool and DeChamps) will not be effect by these survey results.

In appreciation of you participation in this survey, we ask that you enter you contact information, so we can enter you into a drawing for a Applie iPad.

Thank you very much for your time and support. Please start with the survey now by clicking on the Continue button below.

*Please note that the Siemens S7-200 PLC will continue to be supported by Siemens and Munters until 2022
 
 
 
* What controller did you purchase with your last Munters ICA / HCD?
 
Siemens S7-200
 
Allen Bradley MicroLogix
 
Allen Bradley CompactLogix
 
Allen Bradley ControlLogix
 
Don't Know / Remember
 
Other
 
 
 
 
What was primary reason for purchasing your indicated controller for your Munters ICA / HCD?
 
Communications
 
Familiar With hardware
 
Name / Brand / Reputation
 
Availability of 3d party (non-Munters) support
 
Cost
 
Munters Standard / Baseline
 
Familiar with programing / software enviroment
 
Consistent with other controller at Facility
 
Other
 
 
 
How would you rate the following controllers for use as the baseline controller in Munters ICA and HCD product lines?
Acceptable No Preference Unacceptable
* ALC/OEM Ctrl I/O Flex 6126
Brochure / Cutsheet
* Siemens Climatix
Brochure / Cutsheet
* Allen Bradley Micro850
Brochure / Cutsheet
* Siemens S7-1200
Brochure / Cutsheet
 
 
 
Which additional controllers would you like Munters to offer in the ICA / HCD product lines, as options (cost adder may apply), in addition to one of the baseline mentioned above (select all that apply)?
 
Allen Bradley ControlLogix
 
Allen Bradley CompactLogix
 
Siemens S7-300
 
Allen Bradely MicroLogix
 
Other
 

 
 
Please rate the importance of the following controller characteristics when used in an Munters ICA / HCD.
Most ImportantNot Important
5 4 3 2 1
Size
BMS Communication
Availabilty of Non-Munters Support
Cost of Programming Software
Cost
"Industrial" reputation
Reliabilty
 
 
 
* Do you need BMS communications for a Munters ICA / HCD?
 
Required
 
Beneficial, but not required
 
Not Required
 
 
What is your need for each of the communication protocols below?
Prefered Acceptable Not Needed
BacNet MSTP
BacNet TCP/IP
AB Ethernet
ModBus RTU Slave
 
 
 
Additional prefered communication protocols
   
 
 
 
Primary Reason needing a communication protocol with the equipment controller?
 
Remote Status
 
Remote Control
 
Remote Status & Control
 
Other
 
 
 
Thank you for your expressing your opinions.
Pleases provide your contact information so we can enter you into the drawing for the Apple iPad
* First Name : 
* Last Name : 
* Phone : 
* Email Address :