This free survey is powered by
  1. Surveys
  2. 2015
  3. August
  4. F
  5. Faller Level 3

Faller Level 3

Faller Level 3
0%
Exit Survey
 
 
Hello: As a part of our commitment to continued growth, you are invited to participate in our survey. Your survey responses will be strictly confidential and data from this research will be reported only in the aggregate. Your information will be coded and will remain confidential. If you have questions at any time about the survey or the procedures, you may contact Sonya Wiebe at 250-793-5311 or by email at [email protected]. Thank you very much for your time and support. Please start with the survey now by clicking on the Continue button below.
 
 
 
* First Name : 
* Last Name : 
 
 
 
How often do you conduct surveys?
 
Weekly
 
Monthly
 
Quarterly
 
Annually
 
 
 
CAN YOU FALL COASTAL TIMBER UP TO 3M IN
DIAMETER?
 
YES
 
NO, ONLY ACCORDING TO ABILITY DETERMINED BY WORK EXPERIENCE.
 
 
 
NAME THREE POINTS TO CONSIDER IN YOUR INITIAL SAFETY MEETING OR FALLING PLAN.
   
 
 
 
WHEN DO YOU SHUT DOWN DUE TO WIND?
 
WHEN YOU FEEL UNSAFE TO CONTINUE IN THE TIMBER YOU ARE IN
 
AT SPEEDS REACHING 40KM/HR
 
WHEN YOU HAVE YOUR FIRST NEAR MISS
 
WHEN LEAVES START FALLING DOWN
 
 
 
WHERE IS YOUR AXE SUPPOSED TO BE WHEN FALLING
THE TREE?
 
IN YOUR BELT LOOP
 
AT THE BASE OF THE TREE
 
 
 
HOW DO YOU START YOUR TREE FALLING?
 
BY WALKING THE FALLING AREA TAKING NOTE OF HAZARDS
 
SETTING LINERS AND CUTTING IN
 
FLAGGING DANGER TREES SO YOU CAN AVOID THEM
 
 
 
NAME THREE ACCEPTABLE PROCEDURES TO ASSESS AND PREPARE YOURSELF AND THE TREE FOR FALLING
   
 
 
 
SHOULD YOU USE YOUR CHAINBRAKE WHEN CHECKING THE UNDERCUT?
 
YES
 
NO
 
 
 
HOW DO YOU AIM WITH YOUR SAW THE DIRECTION OF
FALL/CONSTRUCTING THE UNDERCUT?
 
BY USING YOUR CHAINSAW SIGHTLINES
 
HOLDING THE SAW AT A 90 TO WHERE YOU WANT IT TO GO
 
JUST GO WITH THE LEAN
 
 
 
HOW DO YOU CLEAN OUT YOUR UNDERCUT?
 
GRAB IT WITH THE SAW TO SPIT OUT THE WEDGE
 
USE THE AXE TO KNOCK OUT THE WEDGE
 
CHECK AND CLEAN OUT IF NEEDED
 
 
 
AFTER YOU STRIKE A WEDGE WHAT SHOULD YOU DO?
 
KEEP HITTING AS FAST AS YOU CAN UNTIL THE TREE FALLS OVER
 
HIT AS HARD AS POSSIBLE
 
WAIT FOR THE ENERGY TO TRAVEL TO THE TOP OF THE TREE BEFORE STRIKING AGAIN
 
 
 
EXPLAIN THE DIFFERENCE BETWEEN PALMING AND SETTING A WEDGE.
   
 
 
 
WHEN ARE YOU ALLOWED TO BACK-BAR A FALLING CUT?
 
WHEN THE TREE IS UNDER 10”
 
WHEN YOU ARE GETTING TIRED
 
NEVER
 
 
 
NAME THE TWO METHODS FOR DETERMINING DIRECTIONAL CONTROL.
   
 
 
 
WHY SHOULD YOU USE TWO WEDGES WHEN APPLYING DIRECTIONAL CONTROL?
   
 
 
 
WHAT FALLING CUT IS USED WHEN FALLING UPSLOPE?
 
HUMBOLDT
 
SWANSON
 
CONVENTIONAL
 
 
 
WHAT SHOULD BE YOUR MAXIMUM UNDERCUT WHEN
DEALING WITH A HEAVY LEANER?
 
10%
 
25%
 
50%
 
 
 
WHEN IS THE ONLY TIME YOU CAN TRY PUSHING/LIMB
TIED TREES?
 
TO OVERCOME SPECIFIC FALLING DIFFICULTIES
 
FOR PRODUCTION PURPOSES
 
WHEN YOU DON’T HAVE TO CUT DOWN AS MANY TREES
 
 
 
HOW MANY ESCAPE ROUTES DO YOU NEED FOR A DANGEROUS TREE?
   
 
 
 
WHAT UNDERCUT DEPTH DO YOU NEED FOR FALLING A
DANGEROUS TREE?
 
10-25%
 
25-40%
 
40-50%
 
 
 
What is the major difference in how to fall a small diameter tree against the lean
 
a larger under cut
 
construct the backcut first, always use a pie cut
 
no wedging required
 
 
 
Name 3 unacceptable fails on a stump check
   
 
Share This Survey:          Surveys Powered by  QuestionPro Survey Software